Idec WindMSG Manual de usuario

We hope that you find this manual informative. If additionalinformation or technical assistance is needed please contact:IDEC Corporation1175 Elko Dri

Register Data Entry:Procedure to a edit register is as follows:1. Press key with definition ‘Accept Data Entry‘ to initiate dataentry mode. Data entry

8. Subtract Tag B from Tag A:*Tag B is subtracted from tag A using this task. The result willbe stored in tag A.9. Turn Bit On:Any coil or bit can be

12. Sign Key (+/-)Used for signed data entry.13. Sign Key (+/-) and 0Single key used as a sign key as well as numeric key 0. Ifthis key is pressed imm

4.4 Application Task-ListApplication task-list allows user to define tasks to be performed atpower-on or while application is running i.e. Global Task

5.1 IntroductionWindMSG is Windows based software to configure the HG1X SeriesInterfaces by IDEC Corporation. WindMSG's tools and easyapproach c

c. Printer Port OptionsHG1X has a Serial Printout Facility. User should connectSerial Printer cable to the Serial Port of the HG1X.Communication param

Define MenuThis menu actually defines the application. In the main window ofWindMSG software, bottom line of the icons is dedicated for thismenu.

5.4 Creating new Application1. Select New from File menu or click on the NewApplication button.2. In the dialog presented, select the HG1X Model and p

5.7 Create Screens1. Select Screens.. from Define menu or Press F6 key orclick on the Screens button.OR2. In New Screen dialog box, enter the Screen n

6. How to define Register Data Entry Object:To edit a register in the PLC, select Register Data Entry inthe Data entry dialog box. Register Data Entry

IntroductionIn this chapter. . . .Purpose of this ManualIntroduction to HG1XHG1X SeriesHG1X-252HG1X-452Normal Operation:Connect HG1X to

11. How to define Alarm object:Alarm object displays alarm immediately after any alarm istriggered. Alarm text is defined in the Alarms dialog box.To

5.10 Application Task-List1. Click on Application Task-List from Define menu or pressF9 or click Application Task-List Button to defineApplication Tas

How Do I?In this Chapter...Frequently asked questions6.1 Frequently asked questionsThis chapter answers the questions user normally asks.1. How c

Appendix AWindMSG TutorialsExample to create Application for HG1XTutorial 1: Create an Application for HG1XModelWe will create an application for HG1X

6. Now we will define Screens. Screens form the most importantpart of any application as it displays the information requiredby the operator. HG1X has

Select Turn bit off task as ‘relesed task’ for the same key.Select coil. Click to accept the task.Now go to screen no 1 using ‘select screen’

Click to define application Task-list for the application. Here wewill define the power-up screen and Global Task-list if any. Selecttask fr

IDEC Micro Smart to HG1X Cable: Pin ConfigurationIDEC Part # HG9Z-SCI25B TXD RXD GNDSHIELD VCCRXDTXDGNDSHIELDVCC346,788356Micro Smart

1.3 HG1X SeriesCurrently models included in the HG1X Series are as follows:HG1X - 252 and HG1X - 452. HG1X Models take power from thePLC. Detailed spe

This chapter is installation guide for HG1X Series.2.1 Installation InstructionsHG1X should be mounted on a panel. Gasket, mounting screws andclamps a

3.1 IntroductionHG1X is an Operator Interface for PLCs. It communicates with a PLCover its serial port to get the information required by the operator

Once the application is defined, firmware for the specific unit andPLC is downloaded and then application is downloaded into the unit.HG1X can now com

- No PLC tag embedding in the screen to be associated. To embed a PLC tag, In Global Task-List the required PLC tag should be copied to an internal

15. Copy Tag to LED:LED’s on the keypad of each HG1X can be turned on/offdepending on the value of a tag. The tag should be copied toLED register and

Check if same keypressedHUpload Alarm BlockServ AlarmDisplay ScreenDisplay Associated ScreensServ While Showing TaskIYNKey Release taskSamekeyPressed